本来的硬件平台是STM32F303VC,ADC校准能通过。换成STM32F303CC，校准就不行了，程序用的老的固件库。ADC的校准需要什么条件才能成功。初始化代码如下：

        ADC_InitTypeDef        ADC_InitStructure;
  ADC_CommonInitTypeDef  ADC_CommonInitStructure;

  /* Configure the ADC clock */
  RCC_ADCCLKConfig(RCC_ADC12PLLCLK_Div1);
//  RCC_AHBPeriphResetCmd(RCC_AHBPeriph_ADC12,ENABLE);  
  /* Enable ADC1 clock */
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_ADC12, ENABLE);
  /* ADC GPIO configuration */
  ADC_GPIO_Configuration();

  /* ADC DMA Channel configuration */
  ADC_DMA_Configuration();
       
  ADC_StructInit(&ADC_InitStructure);
  /* ADC Calibration procedure */
        ADC_VoltageRegulatorCmd(ADC1, ENABLE);
  ADC_VoltageRegulatorCmd(ADC2, ENABLE);

  ADC_SelectCalibrationMode(ADC1, ADC_CalibrationMode_Single);
  ADC_StartCalibration(ADC1);
  ADC_SelectCalibrationMode(ADC2, ADC_CalibrationMode_Single);
  ADC_StartCalibration(ADC2);
        while(ADC_GetCalibrationStatus(ADC1) != RESET )
        {
          calibration_value_1 = ADC_GetCalibrationValue(ADC1);
                debug_log("ADC1 Calibration Value %d",calibration_value_1);
        }
  while(ADC_GetCalibrationStatus(ADC2) != RESET )
        {
                calibration_value_2 = ADC_GetCalibrationValue(ADC2);
                debug_log("ADC2 Calibration Value %d",calibration_value_2);            
        }
//  /* ADC Dual mode configuration */     
  ADC_CommonInitStructure.ADC_Mode = ADC_Mode_RegSimul;                                                                    
  ADC_CommonInitStructure.ADC_Clock = ADC_Clock_AsynClkMode;                    
  ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_1;            
  ADC_CommonInitStructure.ADC_DMAMode = ADC_DMAMode_Circular;                  
  ADC_CommonInitStructure.ADC_TwoSamplingDelay = 1;         

  ADC_CommonInit(ADC1, &ADC_CommonInitStructure);

  /* */  
  ADC_InitStructure.ADC_ContinuousConvMode = ADC_ContinuousConvMode_Enable;
  ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
  ADC_InitStructure.ADC_ExternalTrigConvEvent = ADC_ExternalTrigConvEvent_0;         
  ADC_InitStructure.ADC_ExternalTrigEventEdge = ADC_ExternalTrigEventEdge_None;
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
  ADC_InitStructure.ADC_OverrunMode = ADC_OverrunMode_Disable;   
  ADC_InitStructure.ADC_AutoInjMode = ADC_AutoInjec_Disable;  
  ADC_InitStructure.ADC_NbrOfRegChannel = 16;
  ADC_Init(ADC1, &ADC_InitStructure);
  ADC_Init(ADC2, &ADC_InitStructure);
       
       
   ADC_TempSensorCmd(ADC1,ENABLE);

   ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 1, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_1, 1, ADC_SampleTime_61Cycles5);

   ADC_RegularChannelConfig(ADC1, ADC_Channel_2, 2, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_2, 2, ADC_SampleTime_61Cycles5);
         
   ADC_RegularChannelConfig(ADC1, ADC_Channel_3, 3, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_3, 3, ADC_SampleTime_61Cycles5);

   ADC_RegularChannelConfig(ADC1, ADC_Channel_4, 4, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_4, 4, ADC_SampleTime_61Cycles5);
         
   ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 5, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_1, 5, ADC_SampleTime_61Cycles5);         

   ADC_RegularChannelConfig(ADC1, ADC_Channel_2, 6, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_2, 6, ADC_SampleTime_61Cycles5);

   ADC_RegularChannelConfig(ADC1, ADC_Channel_3, 7, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_3, 7, ADC_SampleTime_61Cycles5);

   ADC_RegularChannelConfig(ADC1, ADC_Channel_4, 8, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_4, 8, ADC_SampleTime_61Cycles5);

   ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 9, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_1, 9, ADC_SampleTime_61Cycles5);

   ADC_RegularChannelConfig(ADC1, ADC_Channel_2, 10, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_2, 10, ADC_SampleTime_61Cycles5);
         
   ADC_RegularChannelConfig(ADC1, ADC_Channel_3, 11, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_3, 11, ADC_SampleTime_61Cycles5);         


   ADC_RegularChannelConfig(ADC1, ADC_Channel_4, 12, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_4, 12, ADC_SampleTime_61Cycles5);
         
         ADC_RegularChannelConfig(ADC1, ADC_Channel_1, 13, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_1, 13, ADC_SampleTime_61Cycles5);
         
         ADC_RegularChannelConfig(ADC1, ADC_Channel_2, 14, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_2, 14, ADC_SampleTime_61Cycles5);
         
         ADC_RegularChannelConfig(ADC1, ADC_Channel_3, 15,ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_3, 15, ADC_SampleTime_61Cycles5);
         
         ADC_RegularChannelConfig(ADC1, ADC_Channel_16, 16, ADC_SampleTime_61Cycles5);
   ADC_RegularChannelConfig(ADC2, ADC_Channel_4, 16, ADC_SampleTime_61Cycles5);

  /* Configures the ADC DMA */
  ADC_DMAConfig(ADC1, ADC_DMAMode_Circular);
  /* Enable the ADC DMA */
  ADC_DMACmd(ADC1, ENABLE);

  /* Enable ADC1 and ADC2 */
  ADC_Cmd(ADC1, ENABLE);
  ADC_Cmd(ADC2, ENABLE);

  /* wait for ADC1 ADRDY */
  while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_RDY));

  /* wait for ADC2 ADRDY */
  while(!ADC_GetFlagStatus(ADC2, ADC_FLAG_RDY));

  /* Enable the DMA channel */
  DMA_Cmd(DMA1_Channel1, ENABLE);

  /* Start ADC1 Software Conversion */
  ADC_StartConversion(ADC1);        

来个大佬指点迷津啊

官方的例程有校准的，参考一下吧 \en.stm32f30x_dsp_stdperiph_lib\STM32F30x_DSP_StdPeriph_Lib_V1.2.3\Projects\STM32F30x_StdPeriph_Examples\ADC\ADC_BasicExample

求LZ的f303的固件库例程，我只有hal库的，不太会用，我邮箱1483060623@qq.com

zhangwf 发表于 2020-7-23 09:55
求LZ的f303的固件库例程，我只有hal库的，不太会用，我邮箱

用CubeMX下载的芯片包里的例程就是固件库的

之前碰过类似问题，校准时候要确保ADC使能位置0