工作中有时候用到需要对PWM波形进行频率和周期的变化，利用DMA Brust时一个比较好的选择，将ST提供的基于F3的例程改到基于F103实现，没什么难度，但是调试的时候最先使用Normal模式导致不宜观察，后改为Circular模式。代码如下：
void TIM1_Init()
{
GPIO_InitTypeDef         GPIO_InitStructure;
DMA_InitTypeDef          DMA_InitStructure;
TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
TIM_OCInitTypeDef        TIM_OCInitStructure;
  uint16_t SRC_Buffer[9] = {4000-1,1,800,10000-1,0,8500,4000-1,2,2000};
  /* TIM1 and GPIOA clock enable */
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1 | RCC_APB2Periph_GPIOA, ENABLE);

  /* DMA clock enable */
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
  
  /* GPIOA Configuration: Channel 1 as alternate function push-pull */
  GPIO_InitStructure.GPIO_Pin =  GPIO_Pin_8;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_Init(GPIOA, &GPIO_InitStructure);  

  /* TIM1 DeInit */
  TIM_DeInit(TIM1);

  /* DMA1 Channel5 Config */
  DMA_DeInit(DMA1_Channel5);

  DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)TIM1_DMAR_ADDRESS;
  DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)SRC_Buffer;
  DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
  DMA_InitStructure.DMA_BufferSize = 18;
  DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
  DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
  DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
  DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
  DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
  DMA_InitStructure.DMA_Priority = DMA_Priority_High;
  DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
  DMA_Init(DMA1_Channel5, &DMA_InitStructure);
  
  /* Time base configuration */
  /* -----------------------------------------------------------------------
    TIM1 Configuration: generate 1 PWM signal using the DMA burst mode:
    The TIM1CLK frequency is set to SystemCoreClock (Hz), to get TIM1 counter
    clock at 24 MHz the Prescaler is computed as following:
     - Prescaler = (TIM1CLK / TIM1 counter clock) - 1
    SystemCoreClock is set to 72 MHz for Low-density, Medium-density, High-density
    and Connectivity line devices and to 24 MHz for Low-Density Value line and
    Medium-Density Value line devices

    The TIM1 period is 5.8 KHz: TIM1 Frequency = TIM1 counter clock/(ARR + 1)
                                               = 24 MHz / 4096 = 5.8KHz KHz
    TIM1 Channel1 duty cycle = (TIM1_CCR1/ TIM1_ARR)* 100 = 33.33%
  ----------------------------------------------------------------------- */  
  TIM_TimeBaseStructure.TIM_Period = 0xFFFF;         
  TIM_TimeBaseStructure.TIM_Prescaler = (uint16_t) (SystemCoreClock / 24000000) - 1;      
  TIM_TimeBaseStructure.TIM_ClockDivision = 0x0;   
  TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;   
  TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure);

  /* TIM Configuration in PWM Mode */
  TIM_OCInitStructure.TIM_OCMode =  TIM_OCMode_PWM1;   
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;         
  TIM_OCInitStructure.TIM_Pulse = 0xFFF;  
  TIM_OC1Init(TIM1, &TIM_OCInitStructure);

  /* TIM1 DMAR Base register and DMA Burst Length Config */
  TIM_DMAConfig(TIM1, TIM_DMABase_ARR, TIM_DMABurstLength_6Transfers);

  /* TIM1 DMA Update enable */
  TIM_DMACmd(TIM1, TIM_DMA_Update, ENABLE);

  /* TIM1 enable */
  TIM_Cmd(TIM1, ENABLE);
  
  /* TIM1 PWM Outputs Enable */
  TIM_CtrlPWMOutputs(TIM1, ENABLE);

  /* DMA1 Channel5 enable */
  DMA_Cmd(DMA1_Channel5, ENABLE);

  /* Wait until DMA1 Channel5 end of Transfer */
  while (!DMA_GetFlagStatus(DMA1_FLAG_TC5))
  {
  }
}

调试时遇到一个问题，在TIM1-CH1测试通过，但是改成TIM8-CH1的时候却不行，有波形输出但是频率、周期不变，求赐教。

TIM8使用TIM_DMACmd(TIM8, TIM_DMA_CC1, ENABLE);测试OK。

我现在自己只会产生一个pwm波，还不会精确控制波形个数。我想问一下有没有完整的工程文件，我是初学者，想修改修改能用的。