小弟有个板子要搞一搞。。 2.4寸的lcd，标识型号FPC-T24QT10T2（搜不到。。。。） 37Pin，不带触摸（有上件位置没上），排除掉已知的pin之后， 剩下的pin非常像是FSMC驱动方式，包括NE1、D0~D15，NOE,NWE,A16都在，剩下一根我猜是reset 然后用确定没问题的（开发板可跑可驱动lcd）代码去试试 读出ID是0x0075 这就糊涂了 ，感觉是读错了，但是完全不知道怎么继续 贴下fsmc初始化和读ID代码： <span style="background-color: white;">void MX_FSMC_Init(void) {     FSMC_NORSRAM_TimingTypeDef Timing;     /** Perform the SRAM1 memory initialization sequence     */     hsram1.Instance = FSMC_NORSRAM_DEVICE;     hsram1.Extended = FSMC_NORSRAM_EXTENDED_DEVICE;     /* hsram1.Init */     hsram1.Init.NSBank = FSMC_NORSRAM_BANK1;     hsram1.Init.DataAddressMux = FSMC_DATA_ADDRESS_MUX_DISABLE;     hsram1.Init.MemoryType = FSMC_MEMORY_TYPE_SRAM;     hsram1.Init.MemoryDataWidth = FSMC_NORSRAM_MEM_BUS_WIDTH_16;     hsram1.Init.BurstAccessMode = FSMC_BURST_ACCESS_MODE_DISABLE;     hsram1.Init.WaitSignalPolarity = FSMC_WAIT_SIGNAL_POLARITY_LOW;     hsram1.Init.WrapMode = FSMC_WRAP_MODE_DISABLE;     hsram1.Init.WaitSignalActive = FSMC_WAIT_TIMING_BEFORE_WS;     hsram1.Init.WriteOperation = FSMC_WRITE_OPERATION_ENABLE;     hsram1.Init.WaitSignal = FSMC_WAIT_SIGNAL_DISABLE;     hsram1.Init.ExtendedMode = FSMC_EXTENDED_MODE_DISABLE;     hsram1.Init.AsynchronousWait = FSMC_ASYNCHRONOUS_WAIT_DISABLE;     hsram1.Init.WriteBurst = FSMC_WRITE_BURST_DISABLE;     /* Timing */     #if 0     Timing.AddressSetupTime = 2;     Timing.AddressHoldTime = 15;     Timing.DataSetupTime = 5;     Timing.BusTurnAroundDuration = 0;     Timing.CLKDivision = 16;     Timing.DataLatency = 17;     Timing.AccessMode = FSMC_ACCESS_MODE_A;     #else     Timing.AddressSetupTime = 10;     Timing.AddressHoldTime = 10;     Timing.DataSetupTime = 15;     Timing.BusTurnAroundDuration = 10;     Timing.CLKDivision = 16;     Timing.DataLatency = 17;     Timing.AccessMode = FSMC_ACCESS_MODE_B;     #endif     /* ExtTiming */     if (HAL_SRAM_Init(&hsram1, &Timing, NULL) != HAL_OK)     {         Error_Handler();     }     /** Disconnect NADV     */     __HAL_AFIO_FSMCNADV_DISCONNECTED(); }</span> 复制代码 读ID代码 <span style="background-color: white;">uint16_t lcdReadReg(uint8_t LCD_Reg) {     uint16_t d;     *(__IO uint16_t*)(Bank1_LCD_C) = LCD_Reg;     d = *(__IO uint16_t*)(Bank1_LCD_D);     return d; } void LCD_Init(void) {     lcdReset(); //  lcdWriteCmd(0x00, 0x0001);     HAL_Delay(50); // delay 50 ms     DeviceCode = lcdReadReg(0x0000);     xprintf("LCD ID:0x%04x\r\n", DeviceCode); //打印LCD ID 。。。 }</span> 复制代码

ID把高8位与低8位颠倒一下