如题，PB3中断进入不了，为什么呢？求大神解答  
NVIC_InitTypeDef NVIC_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
    EXTI_InitTypeDef EXTI_InitStructure;
  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
   RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE);//ÍⲿÖжϣ¬ÐèҪʹÄÜAFIOʱÖÓ
  // KEY_Init();//³õʼ»¯°´¼ü¶ÔÓ¦ioģʽ
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2| GPIO_Pin_3;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;         
    GPIO_Init(GPIOB,&GPIO_InitStructure);                                


    //GPIOB.1 ÖжÏÏßÒÔ¼°Öжϳõʼ»¯ÅäÖÃ
   GPIO_EXTILineConfig(GPIO_PortSourceGPIOB,GPIO_PinSource1);
   EXTI_InitStructure.EXTI_Line=EXTI_Line1;
   EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
   EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
   EXTI_InitStructure.EXTI_LineCmd = ENABLE;
   EXTI_Init(&EXTI_InitStructure);
    //GPIOB.2   ÖжÏÏßÒÔ¼°Öжϳõʼ»¯ÅäÖÃ
   GPIO_EXTILineConfig(GPIO_PortSourceGPIOB,GPIO_PinSource2);
   EXTI_InitStructure.EXTI_Line=EXTI_Line2;
   EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
   EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
   EXTI_InitStructure.EXTI_LineCmd = ENABLE;
   EXTI_Init(&EXTI_InitStructure);   
    //GPIOB.0   ÖжÏÏßÒÔ¼°Öжϳõʼ»¯ÅäÖÃ
   GPIO_EXTILineConfig(GPIO_PortSourceGPIOB,GPIO_PinSource0);
    EXTI_InitStructure.EXTI_Line=EXTI_Line0;
   EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
   EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
   EXTI_InitStructure.EXTI_LineCmd = ENABLE;
   EXTI_Init(&EXTI_InitStructure);  
  
    //GPIOB.3   ÖжÏÏßÒÔ¼°Öжϳõʼ»¯ÅäÖÃ
   GPIO_EXTILineConfig(GPIO_PortSourceGPIOB,GPIO_PinSource3);
    EXTI_InitStructure.EXTI_Line=EXTI_Line3;
   EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
   EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
   EXTI_InitStructure.EXTI_LineCmd = ENABLE;
   EXTI_Init(&EXTI_InitStructure);  


   NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;   
   NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02; //ÇÀÕ¼ÓÅÏȼ¶2
   NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x04;     //×ÓÓÅÏȼ¶1
   NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;        //ʹÄÜÍⲿÖжÏͨµÀ
   NVIC_Init(&NVIC_InitStructure);     //¸ù¾ÝNVIC_InitStructÖÐÖ¸¶¨µÄ²ÎÊý³õʼ»¯ÍâÉèNVIC¼Ä´æÆ÷
  
  NVIC_InitStructure.NVIC_IRQChannel = EXTI1_IRQn;   
   NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;
   NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x01;   
   NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;        
   NVIC_Init(&NVIC_InitStructure);


    NVIC_InitStructure.NVIC_IRQChannel = EXTI2_IRQn;   
   NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;
   NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x02;     
   NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;        
   NVIC_Init(&NVIC_InitStructure);
  
  NVIC_InitStructure.NVIC_IRQChannel = EXTI3_IRQn;   
   NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;
   NVIC_InitStructure.NVIC_IRQChannelSubPriority =0x03;     
   NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;        
   NVIC_Init(&NVIC_InitStructure);

1. RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE);
   
2. GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
   
3. DBGMCU_Config(((uint32_t)0x00000020),DISABLE);/* 解决仿真时JTAG复用口无法输出的问题 */
   
4. 放在IO初始化相应功能之前，自己不会的话第一时间尽量想办法自己搞懂，比别人告诉你更好，数据手册和参考手册都有相应说明。
   

复制代码

PB3为JTDIO口默认，需要remap相应IO口

enjoyfreescal 发表于 2015-8-31 12:40

受教了，其实我是做JAVA的，公司有个项目急，赶鸭子上架。。。。。。刚刚接触几天。表示万分感谢。

木头不流泪 发表于 2015-8-31 12:54
受教了，其实我是做JAVA的，公司有个项目急，赶鸭子上架。。。。。。刚刚接触几天。表示万分感谢。 ...

。。。。

晕，，，，，，，，，，

木头不流泪 发表于 2015-8-31 12:54
受教了，其实我是做JAVA的，公司有个项目急，赶鸭子上架。。。。。。刚刚接触几天。表示万分感谢。 ...

机会很好啊，做Java公司还给你机会做底层，好好把握啊！我一直想做这个，就是专业不对口！

这接受能力 犀利啊

问题解决了吗？同样也加了这两句话还是触发不了中断
/*开启GPIOB的外设时钟和AFIO时钟*/        RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO, ENABLE);                 // 改变指定管脚的映射 GPIO_Remap_SWJ_JTAGDisable ，JTAG-DP 禁用 + SW-DP 使能        GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);

解决了吗