我写的f0xx的配置，这个不行还请修正： void usart1_init(unsigned long BaudRate) { GPIO_InitTypeDef GPIO_InitStructure; USART_InitTypeDef USART_InitStructure; USART_InitStructure.USART_BaudRate = BaudRate; USART_InitStructure.USART_WordLength = USART_WordLength_8b; USART_InitStructure.USART_StopBits = USART_StopBits_1; USART_InitStructure.USART_Parity = USART_Parity_No; USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None; USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;   /* Enable GPIO clock */ RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE); /* Connect PXx to USARTx_Tx */ GPIO_PinAFConfig(GPIOB, GPIO_PinSource6, GPIO_AF_0);  /* Connect PXx to USARTx_Rx */ GPIO_PinAFConfig(GPIOB, GPIO_PinSource7, GPIO_AF_0); /*GPIO_PinRemapConfig(GPIO_Remap_USART1,ENABLE);*/ //f0xx中没有这个函数 /* Enable USART clock */ RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE); /* Configure USART Tx as alternate function push-pull */ GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; GPIO_Init(GPIOB, &GPIO_InitStructure);  /* Configure USART Rx as alternate function push-pull */ GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7; GPIO_Init(GPIOB,&GPIO_InitStructure);  /* USART configuration */ USART_Init(USART1,&USART_InitStructure);  /* Enable USART */ USART_Cmd(USART1, ENABLE); }

怎么用串口1的重映射啊，映射到PB6和PB7上去。PA9和PA10被占用了。搜索

请大神帮忙啊。在线等。

帮顶                       

看看，，，，，，，，，，，

回来结贴。
问题解决了。
这是我调试通过的配置：
void usart1_init(unsigned long BaudRate)
{
    GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;

    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);  

GPIO_PinAFConfig(GPIOB,  GPIO_PinSource6, GPIO_AF_0);  
GPIO_PinAFConfig(GPIOB,  GPIO_PinSource7, GPIO_AF_0);

/* Configure USART Tx as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
/* Configure USART Rx as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;
GPIO_Init(GPIOB,&GPIO_InitStructure);


RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 , ENABLE );

NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;   
NVIC_InitStructure.NVIC_IRQChannelPriority = 0;   
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;  
NVIC_Init(&NVIC_InitStructure);   

USART_InitStructure.USART_BaudRate = BaudRate;
USART_InitStructure.USART_WordLength =  USART_WordLength_8b;
USART_InitStructure.USART_StopBits =  USART_StopBits_1 ;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode =  USART_Mode_Tx | USART_Mode_Rx ;

/* USART configuration */
USART_Init(USART1,&USART_InitStructure);
    /* Enable USART */
//USART_ITConfig(USART1, USART_IT_TC, ENABLE);
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
USART_Cmd(USART1, ENABLE);
}
映射到PA6和PA7上去了。

你好，看来看去是只是加了一个中断配置啊，50M改为10M  映射到底是哪一句啊