在线时间1 小时
UID204986
ST金币0
蝴蝶豆0
注册时间2010-8-3
新手上路
- 最后登录
- 1970-1-1
|
a0a.1 0b0c
#include "stm32f30x.h"
#include "stm32f3_discovery_lsm303dlhc.h"
#define uchar unsigned char
#define uint unsigned int
uchar ge,shi,bai,qian,wan,shiwan; //????
unsigned char Buffer[6];
unsigned char XOffset;
unsigned char YOffset;
static void USART_Config(void)
{
USART_InitTypeDef USART_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
/* Enable GPIOD clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOC|RCC_AHBPeriph_GPIOE , ENABLE);
/* Enable USART1 APB clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
/* Configure the HSI as USART clock */
RCC_USARTCLKConfig(RCC_USART1CLK_HSI);
/* USART1 Pins configuration ***********************************************/
/* Connect pin to Periph */
GPIO_PinAFConfig(GPIOC, GPIO_PinSource4, GPIO_AF_7);
GPIO_PinAFConfig(GPIOE, GPIO_PinSource1, GPIO_AF_7);
/* Configure pins as AF pushpull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_Init(GPIOE, &GPIO_InitStructure);
/* USARTx configured as follow:
- BaudRate = 115200 baud
- Word Length = 8 Bits
- Stop Bit = 1 Stop Bit
- Parity = No Parity
- Hardware flow control disabled (RTS and CTS signals)
- Receive and transmit enabled
*/
USART_DeInit(USART1);
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
/* Enable USART1 */
USART_Cmd(USART1, ENABLE);
/* Before entering the USART in STOP mode the REACK flag must be checked to ensure the USART RX is ready */
while(USART_GetFlagStatus(USART1, USART_FLAG_REACK) == RESET)
{}
/* Enable USART STOP mode by setting the UESM bit in the CR1 register.*/
// USART_STOPModeCmd(USART1, ENABLE);
/* Enable the wake up from stop Interrupt */
// USART_ITConfig(USART1, USART_IT_WU, ENABLE);
/* Enter USART in STOP mode with regulator in low power mode */
// PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
}
void conversion(long temp_data)
{
shiwan=temp_data/100000+0x30 ;
temp_data=temp_data%100000; //????
wan=temp_data/10000+0x30 ;
temp_data=temp_data%10000; //????
qian=temp_data/1000+0x30 ;
temp_data=temp_data%1000; //????
bai=temp_data/100+0x30 ;
temp_data=temp_data%100; //????
shi=temp_data/10+0x30 ;
temp_data=temp_data%10; //????
ge=temp_data+0x30;
}
void Delayms(vu32 m)
{
u32 i;
for(; m != 0; m--)
for (i=0; i |
|