ST意法半导体中文论坛关于STM32F051K4 ADC

关于STM32F051K4 ADC_IN1 的问题请教

huangbo 提问时间：2017-1-22 16:08 /

问答
是否解决:

STM32F051 ADC 配置为DAM 采集 ADIN0~ADIN3, 4通道。
ADIN1输入为0 实测单片机管脚也为0，但是AD出来不正常，
采集结果，串口上传如下：
----AD ch1~ch4 ----

CH0 value = 1.532601 V
CH1 value = 1.458608 V
CH2 value = 0.650549 V
CH3 value = 1.468132 V

CH0 value = 1.531868 V
CH1 value = 1.457143 V
CH2 value = 0.650549 V
CH3 value = 1.468132 V

CH0 value = 1.532601 V
CH1 value = 1.458608 V
CH2 value = 0.649817 V
CH3 value = 1.469597 V

需改代码继续做实验：
AD采样，采用查询方式AD，并串口打印到PC，分别单独作了两个通道采集。
AN2: (注入0.65V)
CH2 value = 0.650549 V
CH2 value = 0.650549 V
CH2 value = 0.649817 V

切换为 AN1

注入0V )
CH1 value = 1.588278 V
CH1 value = 1.509158 V
CH1 value = 1.463004 V

代码基于STM32CubMX 生成，单通道实验，adc.c  如下：
/* Includes ------------------------------------------------------------------*/
#include "adc.h"

#include "gpio.h"

/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

ADC_HandleTypeDef hadc;

/* ADC init function */
void MX_ADC_Init(void)
{
  ADC_ChannelConfTypeDef sConfig;

/**Configure the global features of the ADC (Clock, Resolution, Data Alignment and number of conversion)
*/
  hadc.Instance = ADC1;
  hadc.Init.ClockPrescaler = ADC_CLOCK_ASYNC_DIV1;
  hadc.Init.Resolution = ADC_RESOLUTION_12B;
  hadc.Init.DataAlign = ADC_DATAALIGN_RIGHT;
  hadc.Init.ScanConvMode = ADC_SCAN_DIRECTION_FORWARD;
  hadc.Init.EOCSelection = ADC_EOC_SINGLE_CONV;
  hadc.Init.LowPowerAutoWait = DISABLE;
  hadc.Init.LowPowerAutoPowerOff = DISABLE;
  hadc.Init.ContinuousConvMode = DISABLE;
  hadc.Init.DiscontinuousConvMode = DISABLE;
  hadc.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;
  hadc.Init.DMAContinuousRequests = DISABLE;
  hadc.Init.Overrun = ADC_OVR_DATA_PRESERVED;
  if (HAL_ADC_Init(&hadc) != HAL_OK)
  {
Error_Handler();
  }

/**Configure for the selected ADC regular channel to be converted.
*/
  sConfig.Channel = ADC_CHANNEL_1;
  sConfig.Rank = ADC_RANK_CHANNEL_NUMBER;
  sConfig.SamplingTime = ADC_SAMPLETIME_7CYCLES_5;
  if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
  {
Error_Handler();
  }

}

void HAL_ADC_MspInit(ADC_HandleTypeDef* adcHandle)
{

  GPIO_InitTypeDef GPIO_InitStruct;
  if(adcHandle->Instance==ADC1)
  {
  /* USER CODE BEGIN ADC1_MspInit 0 */

  /* USER CODE END ADC1_MspInit 0 */
/* Peripheral clock enable */
__HAL_RCC_ADC1_CLK_ENABLE();

/**ADC GPIO Configuration
PA1    ------> ADC_IN1
*/
GPIO_InitStruct.Pin = GPIO_PIN_1;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

  /* USER CODE BEGIN ADC1_MspInit 1 */

  /* USER CODE END ADC1_MspInit 1 */
  }
}

void HAL_ADC_MspDeInit(ADC_HandleTypeDef* adcHandle)
{

  if(adcHandle->Instance==ADC1)
  {
  /* USER CODE BEGIN ADC1_MspDeInit 0 */

  /* USER CODE END ADC1_MspDeInit 0 */
/* Peripheral clock disable */
__HAL_RCC_ADC1_CLK_DISABLE();

/**ADC GPIO Configuration
PA1    ------> ADC_IN1
*/
HAL_GPIO_DeInit(GPIOA, GPIO_PIN_1);

  }
  /* USER CODE BEGIN ADC1_MspDeInit 1 */

  /* USER CODE END ADC1_MspDeInit 1 */
}

/* USER CODE BEGIN 1 */

/* USER CODE END 1 */

/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

求大神给予指点！！！谢谢！！