我的颈 发表于 2016-3-28 11:31:40

STM32L073 Nucleo 晒单

本帖最后由 我的颈 于 2016-3-28 12:58 编辑

板子到手了,正在使用中,给我的方案加了一块12864(嘿嘿嘿)做为调试输出

直接用热熔胶粘,建行的网银盾的LCD12864,嘿嘿嘿.
没钱买屏幕只能自己搞了.一块12864也不便宜





上几张分析引脚的图






分析仪抓包喽






代码在附件 哈哈
main
int main(void)
{
   uint8_t Count=0;
   HAL_Init();
   SystemClock_Config();

// BSP_LED_Init(LED2);


   SPI_Conf();
   GPIO_Conf();   
   LCD_Conf();
   LCD_Str(LINE1,10,"www.stmcu.org.cn");
   LCD_Str(LINE2,10,"827230081");
   LCD_Str(LINE3,0,"Please press ");
   LCD_Str(LINE4,0,"the button!");
   HAL_Delay(1000);
   Sensor_Conf();
   BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
   Sensor_Conf();
   while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_RESET);
   LCD_Clear(0);
   LCD_Str(LINE1,10,"Start!");
//   {
//      BSP_LED_Toggle(LED2);
//      Sensor_Conf
//      
//      
//   }
   //BSP_LED_Off(LED2);

   while (1)
   {
   if(SENSOR==SET)
   {
         HAL_Delay(100);
         if(SENSOR==SET)
         {
            LCD_Str(LINE2,10,"Trigger!");
            Count++;         
            //HAL_GPIO_WritePin(GPIOA,GPIO_PIN_4,GPIO_PIN_SET );
         }
   }
   else
   {
      LCD_Str(LINE2,10,"         ");
      //HAL_GPIO_WritePin(GPIOA,GPIO_PIN_4,GPIO_PIN_RESET );
   }
   HAL_Delay(1000);
   if(Count>10)
   {
      HAL_GPIO_WritePin(GPIOA,GPIO_PIN_4,GPIO_PIN_SET );
      LCD_Str(LINE3,10,"BEE!");
      HAL_Delay(1000);
      Count=0;
   }
   else
   {
      HAL_GPIO_WritePin(GPIOA,GPIO_PIN_4,GPIO_PIN_RESET );
      LCD_Str(LINE3,10,"    ");
   }

   
      
   }//end while
   
}//end main12864.c
#include "12864.h"
#include "main.h"

int delay=0;

#define DELAY {delay=0x5f;while(delay--);}                                                                                                                //ÑÓʱ

                                 //81 //
const char CMD={0xAE,0x2F,0x22,0x81,0x3F,0xA2,0xA1,0xC0,0x10,0x00,0xB0,0xA6,0xAF};//²âÊÔÃüÁî•ÖÎöÒÇ×¥µÄ,²»¹ÜËûÖ±½ÓÓÃ

/*×Ö¿â   È¡Ä£•½Ê½ ÒõÂë ÁÐÐÐʽ*/
const char String={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00},/*"!",1*/
{0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00},/*"#",3*/
{0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00},/*"$",4*/
{0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00},/*"%",5*/
{0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10},/*"&",6*/
{0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00},/*"(",8*/
{0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00},/*")",9*/
{0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00},/*"*",10*/
{0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00},/*"/",15*/
{0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00},/*"0",16*/
{0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"1",17*/
{0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00},/*"2",18*/
{0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00},/*"3",19*/
{0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00},/*"4",20*/
{0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00},/*"5",21*/
{0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00},/*"6",22*/
{0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00},/*"7",23*/
{0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00},/*"8",24*/
{0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00},/*"9",25*/
{0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00},/*"<",28*/
{0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00},/*"=",29*/
{0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00},/*">",30*/
{0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00},/*"?",31*/
{0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00},/*"@",32*/
{0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20},/*"A",33*/
{0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00},/*"B",34*/
{0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00},/*"C",35*/
{0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00},/*"D",36*/
{0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00},/*"E",37*/
{0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00},/*"F",38*/
{0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00},/*"G",39*/
{0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20},/*"H",40*/
{0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"I",41*/
{0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00},/*"J",42*/
{0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00},/*"K",43*/
{0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00},/*"L",44*/
{0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00},/*"M",45*/
{0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00},/*"N",46*/
{0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00},/*"O",47*/
{0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00},/*"P",48*/
{0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00},/*"Q",49*/
{0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20},/*"R",50*/
{0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00},/*"S",51*/
{0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"T",52*/
{0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"U",53*/
{0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00},/*"V",54*/
{0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00},/*"W",55*/
{0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20},/*"X",56*/
{0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"Y",57*/
{0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00},/*"Z",58*/
{0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00},/*"[",59*/
{0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00},/*"\",60*/
{0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80},/*"_",63*/
{0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20},/*"a",65*/
{0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00},/*"b",66*/
{0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00},/*"c",67*/
{0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20},/*"d",68*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00},/*"e",69*/
{0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"f",70*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00},/*"g",71*/
{0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"h",72*/
{0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00},/*"j",74*/
{0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00},/*"k",75*/
{0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"l",76*/
{0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F},/*"m",77*/
{0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"n",78*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"o",79*/
{0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00},/*"p",80*/
{0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80},/*"q",81*/
{0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00},/*"r",82*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00},/*"s",83*/
{0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00},/*"t",84*/
{0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20},/*"u",85*/
{0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00},/*"v",86*/
{0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00},/*"w",87*/
{0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00},/*"x",88*/
{0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00},/*"y",89*/
{0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40},/*"{",91*/
{0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00},/*"|",92*/
{0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/

};
void SPI_Conf(void)                        //SPIÅäÖò»¶à˵
{
   SPI_HandleTypeDef SpiHandle;
   
   SpiHandle.Instance               = SPI1;
   SpiHandle.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;
   SpiHandle.Init.Direction         = SPI_DIRECTION_2LINES;
   SpiHandle.Init.CLKPhase          = SPI_PHASE_1EDGE;
   SpiHandle.Init.CLKPolarity       = SPI_POLARITY_LOW;
   SpiHandle.Init.DataSize          = SPI_DATASIZE_8BIT;
   SpiHandle.Init.FirstBit          = SPI_FIRSTBIT_MSB;
   SpiHandle.Init.TIMode            = SPI_TIMODE_DISABLE;
   SpiHandle.Init.CRCCalculation    = SPI_CRCCALCULATION_DISABLE;
   SpiHandle.Init.CRCPolynomial   = 7;
   SpiHandle.Init.NSS               = SPI_NSS_SOFT;
   SpiHandle.Init.Mode            = SPI_MODE_MASTER;
   
   HAL_SPI_Init(&SpiHandle);
   SPI1->CR1   |=1<<6;                                //ʹÄÜ

}
void SPI_SendByte(chartemp)//²»¶à˵
{
   while(!((SPI1->SR>>1)&0x01));
   SPI1->DR=temp;
}



void GPIO_Conf(void)
{
   
   GPIO_InitTypeDef GPIO_InitStruct;


   RCC->IOPENR    |=1<<1;   
   
   GPIO_InitStruct.Mode             =GPIO_MODE_OUTPUT_PP;
   GPIO_InitStruct.Pull             =GPIO_PULLUP;
   GPIO_InitStruct.Speed            =GPIO_SPEED_FREQ_HIGH;
   GPIO_InitStruct.Pin            =GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_6;//GPIO   RST D/C CS
   HAL_GPIO_Init(GPIOB,&GPIO_InitStruct);


}


void LCD_Conf(void)
{
   RST_H;
   CS_H;
   DC_H;
   HAL_Delay(50);
   RST_L;
   HAL_Delay(5);
   RST_H;
   HAL_Delay(5);
   CS_L;
   LCD_CMD(CMD);
   HAL_Delay(2);
   LCD_Clear(0xFF);
   HAL_Delay(2);
   LCD_Clear(0);
   //LCD_SetPoint(LINE1 ,0);
   //LCD_Display(LINE1,10,'1');
   
   
}

/*

*/
void LCD_SetPoint(unsigned char line,unsigned char row)
{
   unsigned char tmp=0;
   DC_L;
   DELAY
   SPI_SendByte(line);                //ÐÐ0xB0
   tmp=0x10+ ((row&0xF0)>>4);//
   SPI_SendByte(tmp);
   tmp=0x04+ (row&0x0F);
   SPI_SendByte(tmp);
   DELAY
   DC_H;   
}
void LCD_DAT(char list,char num)
{
unsigned char i=0;
   DC_H;   
   for(i=num;i<(num+8);i++)
   {
      SPI_SendByte((char )String);
   }
}

void LCD_Clear(char dat)
{
   unsigned char i=0,dummy=0;
   //   LCD_SetPoint(LINE1,0);
   DC_H;
   DELAY
   for(dummy=0;dummy<8;dummy++)
   {
      DC_L;
      DELAY      
      SPI_SendByte(dummy+0xB0);
      SPI_SendByte(0x10);
      SPI_SendByte(0x04);
      HAL_Delay(1);
      DC_H;   
      for(i=0;i<128;i++)
      {
         SPI_SendByte(dat);
//         HAL_Delay(10);
      }
   }
}
void LCD_CMD(constchar * temp)
{
   unsigned char i=0;
   int dummy=0;
   DC_L;

   for(i=0;i<13;i++)
   {
      SPI_SendByte(temp);
      dummy=0x3FF;
      while(dummy--);
   }
   
   DC_H;   
}








/**********--------------------------***********************/

void LCD_Str(unsigned char line,unsigned char row,const char* p)
{
   char i=0;
   i=row;
   while(*p!='\0')
   {
      i+=8;
      LCD_Display(line,i,*p);
      p++;
   }
}
void LCD_Display(unsigned char line,unsigned char row,char temp)
{
   
   unsigned char i=0;
   if((temp-0x20)<0)
      return ;
   LCD_SetPoint(line,row);
   DC_H;   
   for(i=0;i<8;i++)
   {
      SPI_SendByte(String);
   }
   LCD_SetPoint(line+1,row);
   DC_H;   
   for(i=8;i<16;i++)
   {
      SPI_SendByte(String);
   }
   

}




zhangdaijin 发表于 2016-3-28 12:02:46

楼主晒晒代码呗:)

肽宰1 发表于 2016-3-28 12:17:00

:funk::funk::funk:好像很不错啊

disheng4688 发表于 2016-3-28 12:24:43

nice！！！ 谢谢分享

我的颈 发表于 2016-3-28 12:59:33

zhangdaijin 发表于 2016-3-28 12:02
楼主晒晒代码呗

嘿嘿,已上.:lol:lol

我的颈 发表于 2016-3-28 13:00:09

肽宰1 发表于 2016-3-28 12:17
好像很不错啊

还可以,就占用SPI:lol粘的也结实

我的颈 发表于 2016-3-28 13:00:32

disheng4688 发表于 2016-3-28 12:24
nice！！！ 谢谢分享

:lol:lol:victory::lol:victory:

guo8113 发表于 2016-3-28 13:52:54

不错。U盾屏幕可以利用起来了。

加拿大 发表于 2016-3-28 13:58:34

厉害，谢谢分享！

slotg 发表于 2016-3-28 14:13:12

很好的方享。 :D
页: [1] 2 3
查看完整版本: STM32L073 Nucleo 晒单